How to Add or Remove Gliders from Our Slimline & Modern Curtain Tracks
Got too many or too few gliders on your Slimline or Modern curtain track? Don’t worry. It’s a quick adjustment, and I’ll show you how to do it.
Both tracks use the same gliders. The only difference is how you remove the end cap to access them.
These instructions apply to our straight and bay window tracks. You can watch my Slimline demonstration below, then follow the instructions for your particular track.
Important: Always add or remove gliders from the outside ends of your curtain track, not from the middle where the curtains meet.
Watch How to Add or Remove Slimline Curtain Track Gliders
In this short video, I’ll demonstrate how to remove the Slimline end stop, adjust the gliders and put everything back together.
If you have our Modern rounded-face track, the gliders work in exactly the same way, but the end cap is secured with a small screw instead of a twist-lock end stop. I’ll explain that difference below.
How to Add or Remove Slimline Curtain Track Gliders
Introduction
Hi, I’m Lee Stevens from Ezecurtains. In this video, I’ll quickly show you how to remove and add gliders on our Slimline curtain tracks.
This applies whether you’ve bought a straight track or a bay window track.
Removing Gliders
Here we have the track with the end stop locked in and the end cap fitted.
- Hold the end stop, twist it and lift it out.
- Remove the end cap.
- You can now take gliders out or add new ones.
- Once finished, put the end cap back on, drop the end stop into place, twist and lock it securely.
Clipping Gliders In Without Removing the End Stop
It’s also possible to clip gliders directly into the track without taking the end stop and end cap off.
However, you can only add gliders this way, not remove them.
How the Glider Design Works
Looking at the glider from the side, you’ll notice a small slot alongside the two lugs at the top.
This allows the glider to squeeze together slightly and pop into the track.
The eyelet at the bottom is offset to one side. This offset should face into the room so your curtains hang freely in front of the track.
Adding a Glider
Hold the glider with the offset eyelet facing the room.
Hook one side into the track channel, place your thumb behind the glider and push it forwards.
You’ll hear it click into place, and that’s it!
Conclusion
And that’s all there is to it. Now you know how to remove and add gliders on our Slimline track quickly and easily.
I hope this video was helpful. Thank you for watching!
What You’ll Need
You won’t normally need any tools for our Slimline tracks.
- Slimline track: No tools needed. The end stop twists to release it.
- Modern rounded-face track: A small screwdriver to loosen the end-cap screw.
- Any additional curtain track gliders you want to fit.
If you’re only clipping additional gliders directly into either track, you won’t need any tools.
How to Add or Remove Gliders from a Slimline Track
Our Slimline curtain tracks have a twist-lock end stop that holds the end cap securely in place.
1. Start at the Outside End of the Track
Find the outside end of your Slimline curtain track, where you’ll see the end cap and twist-lock end stop.
Always work from the outside end, not the middle of the window.
2. Twist and Remove the End Stop
Hold the end stop between your fingers, twist it to unlock it and lift it out of the track.
You won’t normally need any tools.
3. Remove the End Cap
With the end stop removed, take off the plastic end cap.
This gives you access to the glider channel.
4. Add or Remove Your Gliders
To remove unwanted gliders, simply slide them out through the open end of the track.
To add more, feed the additional gliders into the same channel.
Make sure the offset eyelet on each glider faces into the room.
5. Replace the End Cap and Lock the End Stop
Put the plastic end cap back into position.
Drop the twist-lock end stop into the track, twist it and make sure it’s securely locked.
Finally, check that the gliders slide freely along the track.
How to Add or Remove Gliders from a Modern Rounded-Face Track
Our Modern rounded-face curtain tracks use exactly the same gliders as our Slimline tracks.
The difference is that the Modern end cap is secured with a small screw rather than a twist-lock end stop.
1. Find the End-Cap Screw
Start at the outside end of the track and locate the small screw securing the end cap.
2. Loosen the Screw by One Full Turn
Use a suitable small screwdriver to loosen the screw by approximately one full turn.
You don’t need to remove the screw completely.
3. Slide Out the End Cap
Once the screw has been loosened, simply slide the end cap out of the track.
You can now access the glider channel.
4. Add or Remove the Gliders
Slide unwanted gliders out through the open end, or feed additional gliders into the channel.
As with the Slimline track, make sure the offset eyelet faces into the room.
5. Refit the End Cap
Slide the end cap back into position and retighten the small screw.
Check that the end cap is secure and the gliders move freely.
A Quicker Way to Add Extra Gliders
There’s another method that works with both our Slimline and Modern curtain tracks.
If you only need to add a few extra gliders, you can clip them directly into the track channel without removing the end cap.
- Hold the glider with its offset eyelet facing into the room.
- Hook one side of the glider into the track channel, with the glider angled towards the window.
- Place your thumb behind the glider and push it firmly forwards.
- The glider will compress slightly and click into the channel.
- Check that it’s seated correctly and moves freely.
Important: This method is for adding gliders only. To remove gliders, you’ll need to take off the end cap using the instructions for your track above.
How Many Curtain Track Gliders Do You Need?
The number of gliders you need depends on your curtain heading and how you’ve arranged your curtain hooks.
For pencil-pleat curtains with approximately twice fullness, a useful starting point is around 20 gliders per metre of track.
However, if you’re reusing existing curtains, there’s a simpler way to work it out.
Count the hooks already fitted to your curtains. That tells you how many gliders you’ll need.
You don’t need to leave extra gliders in the track if they aren’t being used.
Slimline & Modern Curtain Track Glider FAQs
Do Slimline and Modern curtain tracks use the same gliders?
Yes. Our Slimline and Modern rounded-face curtain tracks use the same gliders.
The only difference when adding or removing them is how the end caps are secured.
Slimline tracks use a twist-lock end stop, while Modern tracks have a small screw securing the end cap.
Do I need tools to remove the end cap?
For our Slimline tracks, no tools are normally needed. Simply twist and lift out the end stop, then remove the end cap.
For our Modern rounded-face tracks, you’ll need a small screwdriver to loosen the end-cap screw by approximately one full turn. The end cap will then slide out.
Can I remove gliders from the middle of the track?
Always add or remove gliders from the outside ends of the track rather than the middle where the curtains meet.
It’s the simplest way to access the gliders without disturbing the centre fittings.
Can I add extra gliders without removing the end cap?
Yes. On both our Slimline and Modern tracks, you can clip additional gliders directly into the channel.
Hook one side into the channel and push the glider forwards until it clicks into place.
This method only works for adding gliders. To remove them, you’ll need to remove the end cap.
Which way round should the gliders face?
The offset eyelet at the bottom of the glider should face into the room.
This allows your curtains to hang freely in front of the track.
How many gliders do I need?
As a general guide, allow approximately 20 gliders per metre of track for pencil-pleat curtains with around twice fullness.
If you’re reusing existing curtains, count the hooks already fitted to them. That’s the number of gliders you’ll need.
Can I adjust the gliders while the track is fitted?
Yes. You can add or remove gliders while the curtain track is fitted.
If you know you need to make an adjustment before installing the track, it’s usually a little easier to do it beforehand.
