How to Fit a Standard Corded Bay Window Curtain Track (Step-by-Step Video Guide)

Fitting one of our Corded Bay Window Curtain Tracks is easier than you might think. Your track arrives professionally shaped to match your bay window, with the ceiling brackets already positioned on the track for you.

In the video below, I’ll show you how to fit the return wall brackets, clip the track into place and secure the ceiling brackets around your bay. I’ll also demonstrate how to fit the supplied cord tensioner, which is an important part of the installation.

If you’re considering ordering a corded track, this guide will show you what’s involved. And if your track has already arrived, you can follow the video and written instructions as you fit it.

Watch the Corded Bay Track Fitting Video

Tools & Materials You’ll Need

You won’t need specialist equipment. A few basic DIY tools are normally all that’s required.

  • Drill and 6mm masonry drill bit
  • Rawl plugs and screws (supplied with your track)
  • Tape measure
  • Pencil for marking fixing positions
  • Stepladder
  • Screwdriver or power driver

Important: Cord Loop Height and Child Safety

Our corded curtain tracks are supplied with a cord tensioner that must be fitted securely to the wall.

For child safety, the cord loop must be positioned at least 1.5 metres above floor level once installed. That’s why we ask for your track installation height when you order, so we can set the cord length correctly.

Always fit the supplied cord tensioner and keep the cord properly tensioned. Never leave the operating cord hanging loose.

Step-by-Step Fitting Instructions

These instructions relate to our standard glider Corded Bay Window Curtain Track. Your track arrives professionally shaped to match your bay, with the ceiling brackets already positioned. The return wall brackets are fitted separately.

1. Unpack and Check Your Corded Bay Track

Before fitting anything, place your track on a table and have a quick look at how everything is arranged.

  • The ceiling brackets are already spaced around the bay section of the track.
  • Separate wall brackets are supplied for the returns.
  • The ceiling brackets clip onto the track using a small lip and ridge.
  • Once secured to the ceiling, the fixing screws lock the brackets firmly onto the track.
  • Small bracket covers are supplied to hide the fixings and give a neat finish.

You’ll also have the operating cord and its child-safety tensioner. Leave the cord arrangement as supplied while fitting the track.

2. Fit the Wall Brackets on the Returns

Start by fitting the return wall brackets on either side of your bay window. These will support the track while you secure the ceiling brackets.

  • Position each bracket approximately 14–15cm from the bay corner, allowing enough room to clip the track into place.
  • Use the ceiling inside the bay as a reference and mark a level pencil line on the return wall.
  • Mark a second line approximately 2cm higher to position the top of the bracket correctly.
  • Hold the bracket in position and mark the upper and lower fixing holes.
  • Drill using a 6mm masonry bit, insert the supplied plugs and secure the bracket with the screws provided.

Fit the small bracket cover to hide the screws, then repeat on the opposite return.

3. Clip the Track into the Return Brackets

With the wall brackets securely fitted, you’re ready to lift the corded track into position.

This is easier with two people, particularly for a larger bay, although it can be done on your own if you take your time.

  • Hook the track beneath the lip at the front of the return bracket.
  • Twist the track upwards until you hear or feel it click into place.
  • Tighten the small retaining screw underneath the bracket to secure the track.
  • Repeat the process at the opposite end.

With both ends supported, you can now work your way around the bay securing the ceiling brackets.

4. Secure the Ceiling Brackets

The ceiling brackets are already positioned on your track, so there’s no need to work out the spacing yourself.

  • Lift the track into its correct position against the ceiling.
  • Drive a screw through each ceiling bracket and into the ceiling.
  • Work your way around the bay until all the brackets are secured.
  • Check that the track is sitting correctly and feels supported throughout its length.

Some screws may bite directly into timber and feel secure straight away. Others may only catch plasterboard and need a plug for additional support.

5. Check and Improve Any Loose Fixings

Once the track is supported around the bay, go back and check any ceiling fixings that don’t feel completely secure.

If a screw hasn’t gripped firmly, you can improve the fixing using the supplied plug.

  • Remove the screw from the bracket.
  • Slide the bracket slightly to one side to expose the fixing hole.
  • Drill a 6mm hole to the required plug depth.
  • Insert the supplied plug.
  • Slide the bracket back over the hole and refit the screw.

Repeat wherever necessary until you’re happy that the track is securely supported.

Once all the brackets are fixed, clip the remaining bracket covers into place for a neat finish.

6. Fit the Cord Tensioner

The final part of the installation is fitting the supplied cord tensioner to the wall.

This is essential for child safety. It keeps the operating cord under tension and prevents the cord loop from hanging freely.

  • Position the cord tensioner on the wall, ensuring the cord loop will remain at least 1.5 metres above the floor.
  • Hook the operating cord into the tensioner’s pulley to check its position.
  • Remove the cord from the tensioner while marking and drilling the fixing holes.
  • Mark the two fixing holes, drill, insert the plugs and secure the tensioner to the wall.
  • Pull up on the spring ring and refit the cord so it sits correctly under tension.

Check that the cord runs smoothly through the tensioner and remains properly tensioned when you operate the track.

7. Hang Your Curtains and Check the Operation

Once the track is securely fitted and the cord tensioner is installed, you’re ready to hang your curtains.

Use the appropriate pin hooks or nylon curtain hooks for your curtain heading.

With the curtains hanging, operate the track using the cord:

  • Pull one side of the cord to open the curtains.
  • Pull the other side to close them so they meet in the centre.
  • Check that the curtains move smoothly around the bends.
  • Make sure the cord remains correctly tensioned throughout.

Once you’re happy with the movement and everything feels secure, your Corded Bay Window Curtain Track is ready to use.

Thinking About Ordering a Corded Bay Track?

If you’ve watched the fitting video, you’ll have seen how much of the preparation is already done for you. Your track arrives professionally shaped to match your bay, with the ceiling brackets positioned and the cord mechanism ready for installation.

A corded track allows you to open and close your curtains without having to pull on the fabric, which can be particularly useful for larger bay windows.

You can see our Corded Bay Window Curtain Track, choose your options and get a price on the product page.

You only need the overall track length to get a price and place your order. I’ll collect the detailed bay measurements afterwards and check them before your track is made.

Corded Bay Track Fitting FAQs

Do I need special tools to fit my Corded Bay Track?

No. A basic DIY toolkit is normally enough. You’ll need a drill, 6mm masonry bit, screwdriver, tape measure, pencil and stepladder. We supply the standard screws and plugs with your track.

What if a ceiling fixing doesn’t feel secure?

Remove the screw, slide the bracket slightly to expose the hole, drill a fresh 6mm hole and insert the supplied plug. Then slide the bracket back into position and refit the screw.

Do I have to fit the cord tensioner?

Yes. The supplied cord tensioner must be securely fitted to the wall. It’s an essential child-safety component and keeps the operating cord correctly tensioned.

How long will the operating cord be?

We ask for your track installation height when you order so we can set the cord length correctly. The cord loop must be positioned at least 1.5 metres above floor level once installed.

Can I fit the Corded Bay Track myself?

Yes. If you’re comfortable using basic DIY tools, you should be able to fit your track by following the video and instructions. An extra pair of hands can make lifting and positioning the track easier, particularly for a larger bay.

Need Help Choosing the Right Bay Window Curtain Track?

If you’re considering ordering a made-to-measure bay track but aren’t sure whether a corded track would suit your window, I’m happy to help.

You can use the Curtain Track Finder to narrow down your options, or send me a couple of photos of your bay window for personal advice.


Scroll to Top